Pre-Operation SPECIFICATIONS Running horsepower 1.3 HP Air tank capacity 20 gal. If any unusual noise or vibration is noticed, stop the air compressor immediately and have it checked by a trained service technician. Air tanks contain high pressure air. □□ There is a lack of proper ventilation, or the room temperature is too high. General Safety Rules. A line intended only for lights cannot properly carry a power tool motor. Air Compressor; H1820F; Husky H1820F Manuals Manuals and User Guides for Husky H1820F. □□ Keep proper footing and balance at all times. □□ Call an electrician. WARNING: Do not attach air chuck or other tool to the open end of the hose until start-up has been completed. □□ Move the compressor to a well-ventilated area. Operation (continued) 2 Starting the compressor 1 WARNING: Risk of bursting. The air receiver pressure drops when the compressor shuts off. Safety Information (continued) AIR COMPRESSOR AND PNEUMATIC TOOL SAFETY WARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Safety Information (continued) ELECTRICAL SAFETY (SPEED AND WIRING) □□ The no-load pump speed of this product is approximately 3,850 rpm. Using the air compressor in this type of environment may cause damage to the unit. □□ Plug the power cord into a proper receptacle. Service Parts C201H, AIR COMPRESSOR 19 HUSKYTOOLS.com Please contact 1-888-43-HUSKY for further assistance. □□ Turn the air compressor OFF ( O ). Before returning to the store call Husky Customer Service 8 a.m. - 6 p.m., EST, Monday-Friday 1-888-43-HUSKY HUSKYTOOLS.COM Retain this manual for future use. Pre-Operation SPECIFICATIONS Running horsepower 1.3 HP Air tank capacity 20 gal.

Minimum branch circuit requirement 15 A Fuse type Time delay Net weight 73 lbs. The compressor continuously runs. Contain long hair. □□ Check for proper use of extension cord. WARNING: Risk of unsafe operation.

Use eye protection [ANSI Z87.1 (CAN/ CSA Z94.3)] when draining as debris can be kicked up into face. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. User manuals, Husky Air Compressor Operating guides and Service manuals.

Do not use damaged or worn accessories. There is excessive moisture in the discharge air. 3. The regulator outlet pressure must never exceed the maximum pressure rating.

Husky H1820F Operator's Manual (21 pages) Brand: Husky | Category: Air Compressor | Size: 0.78 MB Table of Contents. Do not use the tool while tired or under the influence of drugs, alcohol, or medication. Service Parts (continued) PUMP/MOTOR ASSEMBLY 22. … The air output is lower than normal. For instructions, see Draining the tank on page 15. Questions, problems, missing parts? DUTY CYCLE This air compressor pump is capable of running continuously. NOTE: When using regulator and other accessories refer to the manufacturers instructions. Wire that is heavy enough for a short distance will be too light for a greater distance. Failure to do so can result in serious personal injury. Descriptions are provided for reference only. □□ The safety valve automatically releases air when the receiver pressure exceeds the preset maximum.

WARNING: Your tool may require more air consumption than this air compressor is capable of providing. Troubleshooting (continued) Problem Possible Cause Solution The thermal overload protector □□ There is low voltage from cuts out repeatedly. 5.2 SCFM at 40 PSI Air delivery 4.0 SCFM at 90 PSI Tank Fill-up Time 7 minutes Lubrication Oil free 120V, 60 Hz, Single phase Input AC only, 15 Amps. □□ There is no power to the unit.

WARNING: Risk from noise. the power source. Keep face and other body parts away from outlet of drain. Check the manufacturer’s maximum pressure rating for air tools and accessories. Service Parts (continued) C201H, AIR COMPRESSOR Item Number 33 Description Part Number Nipple, .250-18 X 2.0NPT E107858 34 Label/ Hot Surface E106630 35 Label/ Warning, Drain Tank E106631 Notes: 16 Torque to 10-14 in/lbs 27 Torque to 30-40 in/lbs 30 Torque to 55-100 in/lbs NOTE: Any part number field without a number listed is not available. We appreciate the trust and confidence you have placed in Husk, We strive to continually create quality products designed to enhance your home. Item #0000-000-000 Model #C201H USE AND CARE GUIDE 20-GALLON PORTABLE AIR COMPRESSOR Questions, problems, missing parts? 3. 20 Gal. Proper footing and balance enables better control of the tool in unexpected situations WARNING: Do not wear loose clothing or jewelry. Air pressure 175 PSI max.

Use of any other parts may create a hazard or cause product damage. 21 HUSKYTOOLS.com Please contact 1-888-43-HUSKY for further assistance. 1 WARNING: Risk of bursting. □□ Turn the ON ( I ) / OFF ( O ) switch (1) to the on position, and allow the tank pressure to build. Keep your hair, clothing, and gloves away from moving parts. □□ Check to be sure the unit is plugged in. Failure to heed this warning could result in serious personal injury. Failure to do so could result in possible serious personal injury. Pre-Operation (continued) PLACEMENT OF THE AIR COMPRESSOR WARNING: If any parts are damaged or missing do not operate this product until the parts are replaced. □□ The thermal overload protector is actuated. Troubleshooting Problem The compressor does not run. Pre-Operation (continued) SYSTEM COMPONENTS D A C I F J B E Part H Description A ON ( I )/OFF ( 0 ) Switch: Turn this switch in the “ON ( I )” position to provide automatic power to the pressure switch and “OFF ( O )” to remove power at the end of each use. Download 54 Husky Air Compressor PDF manuals. Operation 1 Preparing for start-up WARNING: Risk of unsafe operation. 3. □□ For voltage, the wiring in a shop is as important as the motor’s horsepower rating. CAUTION: Risk of unsafe operation. 1 WARNING: Risk of bursting.

5.2 SCFM at 40 PSI Air delivery 4.0 SCFM at 90 PSI Tank Fill-up Time 7 minutes Lubrication Oil free 120V, 60 Hz, Single phase Input AC only, 15 Amps. Depending on the environmental conditions, drain the condensate daily and/or every hour. Position the cord so that it will not get caught on lumber, tools, or other obstructions while you are working with a power tool.